For cellulose insulation, Toronto homeowners and landlords can book our crew to blow loose paper fibre onto the attic floor of a house or rental. Cellulose is paper fibre treated with fire retardant. It is one of the loose fills we use for blown-in insulation. We seal the attic floor first, then blow the cellulose to the depth written on your quote.

What cellulose insulation is made of

Cellulose insulation is paper fibre, shredded fine and treated with a fire retardant before it goes in the bag. The retardant is mixed right through the fibre instead of sprayed on the outside, so every handful that lands on your attic floor has it.

The bags come compressed. At the truck, our crew feeds them into a blowing machine. Paddles inside break the fibre apart, and the machine pushes it dry through a hose up to the attic hatch. On an attic floor job nothing gets wetted or glued. Whoever is on the hose lays the fibre across the joists in even passes, starting at the far eaves and working back to the hatch.

The manufacturer's coverage chart sets how many bags go in, based on the floor area and the depth you are paying for. We write that bag count on the quote. You can count the empty bags before we leave.

Cellulose against blown fibreglass

Cellulose is heavier and denser than blown fibreglass. Most of the differences between them come back to that.

We choose blown-in cellulose insulation for an open, dry attic floor with room for depth, and that includes one where the old insulation is still dry. We choose blown fibreglass when you would rather keep the dust down, or when an attic has had a leak: fibreglass copes better if a small leak comes back, though the leak still gets fixed first. If either would do the job, we put both on the quote with their bag counts so you can compare.

Weight and settling

Because the fibre packs tighter, a bag of cellulose covers less floor than a bag of blown fibreglass. Cellulose also settles more after the install, so our crew blows it deeper on the day and it ends up at the quoted depth once it has settled.

Dust on install day

Cellulose throws more fine dust while it is being blown. We tarp the path from your door to the attic hatch, but you will still see some dust around the hatch. Blown fibreglass goes in cleaner, though it is itchy to handle.

Air movement and moisture

Being dense, cellulose does a better job than loose fibreglass of slowing air that drifts through the insulation layer. Water is where it loses out. Cellulose soaks up a leak and hangs on to it, while blown fibreglass dries out faster but lets more air through.

The downsides of cellulose

Compared with blown fibreglass, cellulose is heavier, settles more, holds water from a roof or vent leak and makes more dust going in. That doesn't rule it out. It changes how our crew sets up the job.

  • Heavier: the weight sits on your ceiling, so before we quote we look at the ceilings from below for sags or cracked plaster.
  • Settles more: we blow it past the finished depth and staple depth rulers to the joists, so you can check the settled level later.
  • Holds water: under a roof leak or a dripping vent, a wet patch mats down and stays wet. The leak gets fixed before any cellulose goes in.
  • Dustier install: we tarp the route and the room under the attic hatch, and vacuum the landing when we're done.

Attics that suit cellulose

Cellulose attic insulation suits an open attic floor with clear joist bays and enough height above the ceiling for the depth on your quote. It also works well over existing insulation that is dry. We level the old layer where it's uneven and blow the cellulose on top. A wartime or post-war bungalow in west Toronto or York with an open attic floor is a typical fit.

If the attic is damp, the roof sheathing is stained or the insulation under a leak is wet, the cellulose waits until the cause is fixed and the wet material is gone. Blowing paper fibre over a leak hides the problem and gives the water something to soak into. Tearing out old, wet or rodent-damaged insulation is part of our attic insulation work, and it happens before any new fibre goes down.

Keep it dry: leaks and air first

Roof leaks, bathroom fan ducts and air leaks from below all get fixed before the cellulose goes in, because cellulose holds on to whatever moisture reaches it.

We start with the roof. A drip at the chimney flashing or under a lifted shingle wets the cellulose beneath it, and wet paper fibre mats down and stops insulating. If we spot stains on the sheathing or rafters, we show you, and the roof gets repaired before our crew comes back.

Then the bathroom fans. A fan that vents into the attic, or one whose duct has slipped off, dumps warm, wet air on the insulation every time someone showers. That duct has to run outside before the attic floor is covered.

Air leaking up from the house carries the same moisture. Warm air rises through gaps at the top plates and around wiring and plumbing holes, and the moisture in it condenses in the cold insulation. Our crew seals those gaps on the attic floor first, then blows the cellulose over the sealed floor.

What we check before the cellulose goes in

Our crew goes through this list in the attic before we write the quote, and you can hold any cellulose quote up against it. For the order of work on the day, see our page on what happens on install day.

  • Attic hatch: how big it is, whether it's weatherstripped and insulated, and a clear route to it for the hose that stays out of finished rooms where possible.
  • Wiring and junction boxes: every box has to stay reachable, so we flag and mark each one before it gets covered.
  • Pot lights: we check whether each fixture is rated for contact with insulation. Any that aren't get a cover or clearance before cellulose goes near them.
  • Chimney gap: the gap between the chimney and the framing gets a non-combustible seal, and we keep the cellulose back from it.
  • Bath fan ducts: each one connected and running outside, not ending in the attic.
  • Baffles at the eaves: these go in the rafter bays so the cellulose can't block air coming in through the soffit vents.
  • Old insulation condition: dry insulation stays and gets levelled. Old, wet or rodent-damaged insulation comes out first.
  • Vermiculite: if we find vermiculite, a grey-brown pebbly fill, we stop work, leave it alone and recommend you have a qualified lab or abatement firm test it before any work goes ahead.

FAQ

Common questions about cellulose insulation

Compared with blown fibreglass, cellulose is heavier, settles more, holds water from a roof or vent leak and is dustier to install. None of that rules it out. We blow it deeper to allow for settling, and the leaks get fixed before it goes in.

Cellulose is the better pick for a dry, open attic floor where you want a dense layer that slows air movement. Blown fibreglass is better where leaks are a risk or dust has to stay down. Neither wins in every attic, so we look at yours first and put our recommendation on the quote with the bag count.

Yes, cellulose can go on top of existing fibreglass as long as the fibreglass is dry and has no rodent damage. We pull back the old layer to seal the gaps we can reach, level it, and blow the cellulose over the top. Wet or rodent-damaged fibreglass comes out first.

Yes. Cellulose settles after it is blown in, and it settles more than blown fibreglass does. Our crew blows it deeper than the finished depth so it ends up at the quoted level once it settles. Depth rulers stapled to the joists let you check the level from the attic hatch later.

Get a quote

Book an insulation quote in Toronto

Call (437) 563-1402 or send the form. We'll come and look at the space, go over the options with you and give you a firm quote.

Call Text Quote